My Gambuino Clone

Show us your Gamebuino clone or the last module you made.

My Gambuino Clone

Postby spunky » Thu Mar 03, 2016 3:13 am

FINISHED.png
ready to print at pcb shop,not shure if it will even work,i get 3 for £40 i think they will work,ive gone over the schematic enough times,shame the board is square lol its gona be small though 10cm x 8cm and it takes an sd card breakout,it plugs in on the left where the 6 pin header is,battery will go in center its got no charge circuit but will have a ftdi for bootloader etc i just hope ive got the screen leds lined up properly i can see that being a bugger but may be lucky with it.
FINISHED.png (82.12 KiB) Viewed 5555 times
Last edited by spunky on Thu Mar 03, 2016 3:29 am, edited 2 times in total.
spunky
 
Posts: 10
Joined: Thu Mar 03, 2016 3:03 am

Re: My Gambuino Clone

Postby spunky » Thu Mar 03, 2016 3:19 am

my clone 1.jpg
both my clones
my clone 1.jpg (65.71 KiB) Viewed 5554 times
spunky
 
Posts: 10
Joined: Thu Mar 03, 2016 3:03 am

Re: My Gambuino Clone

Postby spunky » Thu Mar 03, 2016 3:19 am

my clone 2.jpg
my other clone
my clone 2.jpg (70.68 KiB) Viewed 5554 times
spunky
 
Posts: 10
Joined: Thu Mar 03, 2016 3:03 am

Re: My Gambuino Clone

Postby Retrogadgets » Sat Mar 05, 2016 9:51 am

spunky wrote:
my clone 1.jpg



checkout www.dirtypcbs.com you could have had 10 boards for £29.00 with a 10 days delivered back to you from china !
theyre great quality
Retrogadgets
 
Posts: 8
Joined: Sun Feb 14, 2016 3:53 pm

Re: My Gambuino Clone

Postby albertinjo » Wed Mar 09, 2016 12:01 pm

Nice
Here's mine
Spunky your scrren is probabbly flickering? Mybe i'm wrong, anyway...put a large capacitor near the screen power supply and it should be a lot better... took me a while to figure out
SAM_3259.JPG
SAM_3259.JPG (215.81 KiB) Viewed 5485 times
User avatar
albertinjo
 
Posts: 98
Joined: Wed Mar 26, 2014 2:26 pm

Re: My Gambuino Clone

Postby spunky » Fri Sep 23, 2016 9:09 pm

Hi,my screen is ok no flicker or anything,my sound isnt that loud but its ok,i didnt amp it up with a transistor lol but it works fine,yours looks great.
spunky
 
Posts: 10
Joined: Thu Mar 03, 2016 3:03 am

Re: My Gambuino Clone

Postby spunky » Fri Sep 23, 2016 9:10 pm

Why have you 3 switches at the bottom?
spunky
 
Posts: 10
Joined: Thu Mar 03, 2016 3:03 am

Re: My Gambuino Clone

Postby rodot » Mon Sep 26, 2016 7:47 am

Albertinjo said in this post that it was for backlight control and manual muting.
User avatar
rodot
Site Admin
 
Posts: 1290
Joined: Mon Nov 19, 2012 11:54 pm
Location: France

Re: My Gambuino Clone

Postby Retrogadgets » Fri Oct 07, 2016 6:13 pm

My gamebuino compatible - The MAKERbuino in partnership with Albert Gajšak
Retrogadgets
 
Posts: 8
Joined: Sun Feb 14, 2016 3:53 pm

Re: My Gambuino Clone

Postby Retrogadgets » Fri Oct 07, 2016 6:31 pm

A diy version of gamebuino with standard components, no surface mount technology

our website at http://www.makerbuino.com/

tindie shop at https://www.tindie.com/products/dava_2/ ... rod_search

see you there
Attachments
20161007_192822.jpg
20161007_192822.jpg (167.2 KiB) Viewed 4668 times
Retrogadgets
 
Posts: 8
Joined: Sun Feb 14, 2016 3:53 pm

Next

Return to Hardware Gallery

Who is online

Users browsing this forum: No registered users and 1 guest

cron